PitStopUSA.com - Driveshafts
Select a Sub-Category
- Allstar Performance
- BMR Suspension
- Brinn Transmission
- Chassis Engineering
- Coleman Racing Products
- Competition Engineering
- Detroit Speed Engineering
- Falcon Transmission
- Ford Racing
- Frankland Racing Supply
- Lakewood Industries
- M&W Aluminum Products
- Mark Williams Enterprises
- Moog Chassis Parts
- Moroso Performance Products
- Moser Engineering
- MPD Racing
- Quarter Master
- Racing Power
- Richmond Gear
- Sander Engineering
- Strange Engineering
- Sweet Manufacturing
- TCI Automotive
- TEN Factory
- Ti22 Performance
- Tiger Rear Ends
- UB Machine
- UMI Performance
- USA Standard Gear
- Wiles Racing Driveshafts
- Winters Performance Products
- Yukon Gear & Axle
More About Driveshafts
Courtesy of PST - Precision Shaft Technologies
Step 1: Identify Transmission
Chrysler – Dodge
- 727 - 30 Spline 1 11/16" Seal Diameter
- 904 - 26 Spline 1 9/16" Seal Diameter
- C6-T56 - 31 Spline 1 11/16" Seal Diameter
- AOD & C4 & T5 - 28 Spline 1 1/2" Seal Diameter
- 4 R 7OW - 28 Spline 1.598" Seal Diameter
- T-350 700R4-4LLOE - 27 Spline 1 1/2" Seal Diameter
- T-400-4L80E - 32 Spline 1 7/8" Seal Diameter
Note: Transmission slip yokes are manufactured with various U-Joint Series. It is important to match Horsepower and Torque requirements to U-Joint Series. For aftermarket transmission applications usually a spline count and seal diameter will identify slip yoke required.
Step 2: Identify Rear U-Joint
If Pinion Yoke has Placement tabs that retain the U-Joint, measure inside tabs. See Diagram D.
If Pinion Yoke does not have Placement Tabs that retain U-Joint, measure from flat of yoke inside to inside. See Diagram E.
If 4 bolt Flange is used on pinion, measure Pilot Diameter and center to center diagonally bolt hole to bolt hole. See Diagram L.
Universal Joint Size. There are hundreds of U-Joint sizes or "Series" to accomodate many different applications of power and desired longevity for your automotive, 4x4 truck or auto racing requirements, these 4 series of joints cover most needs.
1310 Spicer Series: 1 1/16" Cup Diameter (Dim C - Diagram A) 3 7/32" length (Dim B - Diagram A) Certain Ford applications have 2 cups 1 1/8 Diameter. Appropriate horse power range is up to 500 in circle track or road racing, small tire drag racing and 4x4. Also available: Performance Dynamic Cryo Joint.
1330 Spicer Series: 1 1/16" Cup Diameter (Dim C - Diagram A) 3 5/8" length (Dim B - Diagram A) Certain Ford applications have 2 cups 1 1/8 Diameter. Slightly stronger than 1310, Used in 5.0 Mustangs. Also available: Performance Dynamic Cryo Joint.
3R Saginaw Series: 1 1/8" Cup Diameter (Dim C - Diagram A) Retained with internal clip 2 5/8" (Dim B - Diagram A). Most common GM joint. Horse power range up to 700 in road racing and circle track. Solid drag racing U-Joint can accomodate most sportsman classes. Also available: Performance Dynamic Cryo Joint.
1350 Spicer Series: Manufactured with OEM tolerances and treated with our Cryogenic Process to yeild the strongest U-Joint available. For drag racing applications a solid non-lube design U-Joint is recommended because of the tremendous initial shock load, or short duration of high torque the joint must be able to withstand.
Step 3: Driveshaft Measurements
NOTE: Driveshaft measurements are from U-joint center line to U-joint center line.
If PST is supplying you with transmission slip yoke, Pinion yoke and driveshaft yoke measure Dim W. See Diagram N.
If PST is supplying you with transmission slip yoke and driveshaft measure Dim X. See Diagram N.
2 Piece driveshafts use Dim Y + Z. See Diagram N.Pit Stop USA is the Online Motorsports Superstore! We feature Driveshafts, Driveshaft, Drive Shafts, Drive Shaft, Racing Driveshaft, Racing Drive Shafts, Driveline Components, Drivetrain Components', Driveshafts, Driveline Components, Drivetrain Components' at low everyday prices!