Home - Brands - Competition Engineering
Additional Images

Competition Engineering 3-Way Adjustable Front Drag Shock

Shock, Drag, Monotube, 11.00 in Compressed / 16.50 in Extended, 1.63 in OD, 3 Way Adjustable, Steel, Gray Paint, Front, Each
Limited Supply: only 2 remaining
Availability: Same Day Shipping!
Shipping: Ships from Michigan.
Was: $58.99
Sale: $58.40
Save: 1%
Save: $0.59


Competition Engineering's 3-Way Adjustable Drag Shocks are designed to allow the racer to dial-in the race car to meet changing track conditions. Shock valving plays a very important role in the way your car will perform both during initial launch and throughout the quarter mile.

The principle behind our shock absorber design is to allow the front end of the race car to rise rapidly upon initial launch, creating greater weight transfer and better traction to the rear tires. As the car travels down the track, the front end will gradually descend to its ride height without unloading the rear tires which is a major cause of wheel spin. Our rear shocks work in conjunction with our front shocks making the transition from initial launch to top end charge as smooth as possible.

When using Competition Engineering's Rear Drag Shocks with a leaf spring suspension, you will see a greater amount of chassis separation than before. This means that your suspension is working to plant the rear tires to give you the utmost in traction. For cars with rear coil springs and factory four link, you will notice increased squat in the rear suspension which will apply more weight to the rear tires increasing their traction.

Competition Engineering's Front Drag Shocks are adjustable in three ratios: 90/10, 80/20 and 60/40. These ratios reflect the percentage of force required to extend and compress the shock absorber. You can quickly change the valve setting by simply compressing the shock fully and rotating the shaft until the indexing notch mates with the desired setting on the body. It's as simple as twist and click.

Our Rear Drag Shocks are also adjustable in three ratios: 30/70, 40/60 and 50/50. These ratios also represent the percentage of force required to compress and extend the shock unit. Only this time the first number is compression and the second extension. These shocks also adjust by compressing them fully and rotating to the desired setting on the body.


  • 1967-62 Chevrolet w/ Multileaf Rear Springs
  • Extended Length: 16.50
  • Collapsed Length: 11.00
  • NOTE: These shocks are designed for DRAG RACE use only! Not for street use.

    Spec Sheet

    Tech Tip
  • To fine tune the amount of weight transfer to the rear suspension for lower ET's, use Competition Engineering 3-Way Adjustable Shocks together with our Rear Drag Race Springs.
  • Rotate Competition Engineering's Adjustable Drag Shocks' shaft several revolutions with a wrench to free up the internal components before installing the shock in the car for the first time. This will make subsequent tuning adjustments easier.
  • When mounting rear shocks on a drag race vehicle you want them to be 90 degrees from the axle centerline. On street cars, you can tilt the top of the shocks inboard 5 -10 degrees for better handling.
  • Before weighing your vehicle, make sure that it is race ready - driver on board, full load of fuel, and the correct amount of ballast added.

    Pit Stop USAoffers Competition Engineering 3-Way Adjustable Front Drag Shock at low everyday prices. Be sure to check out all of our products from Competition Engineering including Competition Engineering 3-Way Adjustable Drag Shocks at low everyday prices.
  • PROP 65

    These products may contain a chemical known to the state of California to cause cancer and birth defects or other reproductive harm


    • COE2605
    • COE2605
    • 0084663026058
    • Competition Engineering
    • Available
    • Same Day Shipping!
    • New

    Shipping Information

    • Item Requires Shipping
    • 2.9 lbs.
    • W3.6000” x H2.3000” x L16.8000”
    • Ships from Michigan.


    Customer Reviews

    Comment Total Reviews (0)

    Write the First Review!

    You must login to post a review.